How Big of a Hole Should I Drill to Fit a Garden Hose
Garden hose reels and hoses come in all different sizes. Some are flexible, some are hard plastic and there are also those that are made of metal and have a rubberized inner core for added strength. The hole that you need to drill to fit the hose is going to vary depending on the hose length and the diameter of the hole you need to drill. The diameter of the hole you drill depends on the amount of water that flows through the hose at one time.
For example, say you are using a 24-inch hose and you want to drill a hole in a tree. The diameter of the hole you make will be approximately five feet, five inches on each end. If you had a hose with a twenty-four inch hose length and diameter and you wanted to drill a hole in a tree with a five foot diameter tree, you would need to make the following adjustments. You would need to make an appropriate cut in the hose so that you did not cut any of the rubber insulation. The next step is to add a washer and a nut on the opposite ends of the two wires so that the entire assembly can be tightened.
Another example might be sanding a garden hose to the correct diameter. First you will need to take your garden hose and measure the outside diameter of the actual hose. Next you will want to add two and a half inches to the outside diameter to get the width of the hose. You then take the piece of wire that the hose will hook up to and you will wrap it around the house about six inches from the front. Once you have wrapped it you will tighten the wire.
To determine how big of a hole to drill for a garden hose all you have to do is open up the washer and nut and pull the wire tight. How long will the house be before you determine that it is not big enough? Usually it will take between six and twelve inches before you decide that the hose is not big enough. If you have a lot of insulation on the outside of your house you can drill several holes and then put on the insulation. You may also have to buy some additional fittings and tools to be able to complete the job.
A garden hose that is made of brass or steel will resist corrosion and rust. The best metals for this purpose are iron and copper. In order to determine how big of a hole I should drill to fit a garden hose all you have to do is stand the hose up and measure how high the attachment end is. You can determine the diameter of the hose by multiplying this number by the height of the attachment.
Another consideration when trying to determine how big of a hole should I drill to fit a garden hose is what material to use. If you are using steel tubing, the diameter will be greater than if you used copper or brass. Most of the hose attachments are made of nylon or other lightweight materials so they will work well in almost any weather conditions. If you are using stainless steel to drill the hole, you will need to apply oil to the drill bit so that it does not rust when it touches the steel. This oil will protect the metal from any moisture that may be present.
If you have questions about how big of a hole I should drill to fit a garden hose you can ask your local hardware store clerk or you can contact a professional landscaper to get the answer to that question for you. They will be able to tell you better than anyone else just exactly how much material you will need to drill that hole and how big of a hole you will need to drill it for the garden hose that you are using. There are a few other things to consider when trying to determine how big of a hole to drill to fit a garden hose. One thing that you should keep in mind is how long the hose will actually stay out in the ground. If you take a measurement before you start digging, you will have an idea of how long the hole will be before it becomes obtrusive and you have to rip up the dirt.
If you do decide to use a piece of rope to help you measure the hole, be sure to add an inch to the length you want the rope to be. Also, be sure to be very accurate with the length of the rope. You do not want to find out at the end of the day that you are one inch short of the exact length of the hose that you needed to complete the job. These are just a few things that you will want to keep in mind when trying to figure out how big of a hole I should drill to fit a garden hose. It can become a bit of a hassle, but it can also save you time and money if you make the right measurements and order the correct equipment to do the job.
View more:
Best Garden Augur Drill Bits Mykeenhome on Live Journal
Best Garden Augur Drill Bits Mykeenhome on Behance
